The 10 Scariest Things About Repair Car Keys

How to Repair Car Keys

Car keys might seem small and insignificant, but they are crucial to the operation of your vehicle. The cost of replacing a traditional or modern transponder mobile car key repair near me key can range from $200 to upwards of $200.

There are methods to repair your car keys at home for a fraction of the cost. This article will address the most frequent car keys issues as well as the DIY solutions to fix them.

Dead Key Fob Battery

Cars are equipped with remote key fobs that allows opening the doors, trunk and tailgate easier than ever before. The battery of the device is prone to dying. There are a few tricks you can use to solve this issue quickly.

First, determine if the car is still in ignition mode. If so the battery of the key fob might be low instead of dead. To test this, push the button on the key repair fob right towards the ignition button. If this does not work, the battery is probably in good condition and requires to be replaced.

To replace the fob's battery, start by prying open the case with a screwdriver or watch-type tool. Be careful not to apply too much pressure since this could cause the fob's to split into two pieces. If the fob isn't opening open with ease, try placing your pry tool into several places on the outside of the case.

Open the electronic part of your vehicle after you have removed the mechanical key. Insert the new battery and snap it back into the shell. If your key fob still isn't working after this procedure, it could be an problem with the remote starting system of your car. This requires an expert to identify. A reputable mechanic will be in a position to assist you if this is the situation. You can also reach out to roadside assistance for help with your vehicle if needed.

Broken Key Ring

There are a few steps you can do in the event that your key fob won't work because the ring is broken. Check to see if you can locate the broken part within the ignition. If it's still there, remove it without causing damage to the ignition lock or the door lock. Call a locksmith if you have difficulty removing the key. They have tools that can safely remove a damaged key from the ignition.

A broken car remote key fob repair key could also be caused by corrosion on the plastic frame or circuit board. Clean the circuit board using cotton swab. This will eliminate corrosion and ensure the contact pads don't get damaged.

If your key won't start because the ring is broken or was damaged, you might be able to repair it by using a thick wire or nail to plug the hole. You can also use superglue to repair a broken ring. First, clean the damaged ring with a damp cloth and then apply a small amount of superglue on each end of the nail or wire. Apply the glue to the ring and allow them to dry before using your car. These DIY solutions may seem appealing, but they're only temporary solutions. For long-term repairs, it's best to hire an experienced locksmith. They have the expertise and tools to repair a broken key quickly and effectively. They can even replace the battery on your key fob and change it's programming if required.

Broken Key Blade

Some key blades break because of a lot wear and tear. If this occurs, you ought to purchase a new one. Fortunately, the issue isn't as serious as it appears at first glance. The most significant issue is that the blade broke off from the case.

Spraying lubricant into the keyhole is one way to repair it. Then, you can use pliers tweezers, or a pin to grasp the broken end of the key and remove it. If the key is magnetic, you can also try using a magnet to assist in pulling it out. Use a magnet as a aid to you remove the key, but be cautious to not sever the tumbler of the lock.

If you're not able to get the broken piece of the key, call an expert locksmith immediately. They have tools that permit them to safely remove keys without causing further damage.

Super glue can be used to fix a snapped lock. Apply a small amount of glue to the edges of the break and press them together. Then, wait until the glue is dry before inserting your key into the lock. This method isn't reliable and you might have to repeat the process a few times before it's successful. Plus the super glue may not be enough strong to hold the key together. Therefore, this is more of a temporary measure than a permanent solution.

Broken Plastic Loop

If the plastic loop is damaged it could render the key useless. It's a fairly simple fix. As a replacement, you can use an extremely thick wire or a finishing nail. Drill two holes in the broken plastic loop for each end of the wire or nail. Cut the nail or wire to the desired width and then put a drop of superglue in each hole. Then, press the wire or nail into the holes to seal them, and then let it dry.

A locksmith who sells replacement shells is a different option. They can take the programmable part of your key, transfer it to the new shell and cut a new blade for much less than the full replacement cost.

It's not the ideal solution, but it can get you back on the road in case your key split in half. It's difficult to repair when the key blade is in the ignition however. If you're not cautious you can make use of a hair clip or a needle to take the damaged part from the ignition. The best option is to contact a locksmith with special tools to safely remove broken keys from the ignition. They can also design a new key with the proper cuts for your ignition, so it will work correctly when inserted into the lock.

Broken Master Key

You'll need to at regaining the key before it is completely destroyed. You can use tweezers, lubricants, and needle nose pliers to grasp the broken fragment of a key.

Spray the inside of the lock with WD-40 or graphite powder. You can also use the hacksaw blade method, which involves sliding the blade along the sides of the broken key, and then grasping a few of its 'teeth. If you're successful then you should be in a position to remove the broken key.

Many hardware stores offer the spiral key extraction tool. It is a thin rod with spiral threads that can be placed in the keyway, and then bent to the broken portion of the key. Once it has gotten caught on the serrations you can twist the bar into a circle and then pull it up against the broken section of the key.

It's worth attempting to remove a master key that's broken prior to calling an expert locksmith. If you're not able to get rid of the broken piece then you'll have to call in the professionals. A locksmith can give you a new key that can be programmed using the transponder in your car.