The 10 Scariest Things About Repair Car Keys

How to Repair Car Keys

Car keys might seem tiny and insignificant, but they are vital to the operation of your vehicle. Replacing a traditional key or a modern transponder key can cost upwards of $200.

There are methods to keyless entry repair your car keys at home for only a fraction of the cost. This article will address the most common car keys issues as well as their DIY solutions.

Dead Key Fob Batteries

Cars come with remote key fobs that allows opening the doors, trunk and tailgate easier than ever before. However, the battery in this device can die. Fortunately, there are a few tricks that can be used to solve this problem in the event of a need.

First, determine if the car is still in ignition mode. If it is, then the battery on the key fob could simply be depleted instead of dead. To test, press the button on the fob against the ignition button on the vehicle. If this works, then the battery is probably in good condition and only needs to be replaced.

To replace the battery within the fob, you need to open the case using an screwdriver. Don't apply too much force as this may cause the fob's casing to split. If the fob won't open, try using your pry tool more than once around the outside of case.

Open the electronic portion of your car key repair once you have removed the mechanical key. Install the new battery and snap back the shell. If the key fob isn't working after this procedure, it could be due to a larger issue with the remote start system of your vehicle. This requires an expert to determine the cause. A reputable mechanic will be able help you in this situation. You can also contact roadside assistance to assist with your vehicle if needed.

Broken Key Ring

There are a few things you can do if your key fob doesn't work because the ring is broken. The first step is to see if your broken piece is still in the ignition. If it is, you should remove it without damaging the ignition lock or door lock. If you are having trouble getting it out, contact a locksmith for help. They have special tools that can safely remove a damaged key from the ignition.

Another common cause of a broken car key repair near me key is the corrosion of the circuit board or plastic frame. You can clean the circuit board by using a cotton swab soaked in rubbing alcohol. This will eliminate the corrosion and protect to the contact pads.

If your key isn't starting because of a broken ring, you may be able to fix it using a sturdy wire or nail to seal the hole. You can also use superglue to repair a broken ring. First, clean the broken ring with a damp cloth and then apply a small amount superglue to each end of the wire or nail. Allow the pieces to dry, and then press them into place. These DIY solutions might appear appealing, but they're only an interim measure. It's best to hire an expert locksmith for repairs that last. They have the experience and tools to fix the broken key quickly and efficiently. They can replace the battery and reprogram the key fob, if needed.

Broken Key Blade

Some key blades might break due to wear and tear. If this happens, you should probably buy a new one. This problem isn't nearly as serious as you might think at first glance. The main problem is that the blade broke off from the case.

Spraying lubricant into the keyhole is a method to repair car keys it. Then you can use pliers, tweezers, or a pin to grasp the broken end of the key and pull it out. You can also employ a magnet in the event that the key is magnetic. Use a magnet as a aid to you remove the key, but be cautious to not sever the lock tumbler.

If you're unable to get the broken piece of the key, contact a locksmith right away. They have the right tools to safely extract keys without causing further damage.

You can also use super glue to fix a broken key. Apply a small amount of glue to the edges and press them in. Make sure the glue is dry before inserting the key into the lock. This method isn't secure and you may need to repeat the process a few times before it is successful. Super glue might not be able to hold the key together. This is more of a temporary measure rather than a permanent solution.

Broken Plastic Loop

If the plastic loop is damaged it could render the key useless. It's an easy fix. You can use thick wire or a finishing nail as a replacement. Drill two holes in the plastic loop that is broken at each end of the nail or wire. Cut the wire or nail into a key width, and then place one drop of superglue into each hole. Press the wire or nail into the holes until it closes them and let it dry.

A locksmith who sells replacement shells is an alternative option. They can remove the programmable portion of your key, transfer it to the new shell, and cut the new blade for less than a full replacement cost.

It's not the most ideal solution, but it'll bring you back on the road in case your key broke in half. It's not easy to repair when the blade of the key is in the ignition, however. You can try using a hair clip, a needle or an extractor tool to pull the broken piece of the ignition, however this is risky if you're not careful. Call a locksmith with special tools to safely remove broken keys from ignitions. You can also have a new key that is made using appropriate cuts to fit the ignition of your car.

Broken Master Key

If a key gets damaged inside the lock, you'll have to find it before it gets completely destroyed. You can make use of the tweezers, lubricants and needle nose pliers for grabbing the broken fragment of a key.

Spray the inside of your lock with WD-40 or a graphite powder. You can also employ hacksaw blades by moving the blade along the side of a broken key and grasping onto a few of its 'teeth. If you're successful then you should be in a position to remove the broken key.

Another tool that is useful is a spiral key extractor that can be found in a wide range of hardware stores. This has a thin flexible bar with spiral threads which can be put into the keyway, and then bent to reach into the broken section of the key. Once it has caught onto the serrations, you can turn the bar into a circle and then pull it against the damaged section of the key.

Before contacting a locksmith try to get rid of the broken master key. If you're not able to remove the broken piece then you'll have to contact a professional locksmith. A locksmith can make you a new key that will be programmed with the transponder of your car.