The 3 Biggest Disasters In Audi G28 History

How to Replace an audi replacement key Cost uk G28 Engine Speed Sensor

In this video, Charles the Humble Mechanic demonstrates how to replace the G28 engine speed sensor. This sensor is located at the edge of transmission just above the flywheel gear. It sends a message to the ECU through an uncolored wire T55/49, then to the tachometer on the instrument cluster.

1. Engine Speed Sensor

It is located on the outside of the transmission above the flywheel ring gear G28 Engine Speed Sensor sends signals to ECU pin T55/49 using the grey wire. The ECU uses this information to control boost and fuel. It also sends an indication to the G5 Tachometer located in the instrument cluster.

The sensor is used to correlate with the G40 Camshaft position Sensor. The ecu needs to know when the crankshaft has reached TDC and also the position of the camshaft, in order to activate the spark and injectors.

If this sensor fails, the ECU will display a P00160 error code. This means that the Crank Shaft is audi tt key fob not working in sync with the Intake Camshaft. It could also be a sign of the possibility of a chain stretch or jump in the chain link of the upper timing chain. However the code will not be displayed on its own without additional information from other sensors (G4 and G40).

Testing is a bit challenging as there are two different pins for the connector and they perform different functions however the best method to test it is to measure the resistance between the sensor and the ECU. It should read approximately 1000 ohms if the sensor is in full operation. Look for evidence of coolant or oil in the connector bay if you have problems with this part.

2. Injectors

Yesterday, while accelerating at full speed from the highway paytoll, I experienced a big cut in power as if the engine was running out of gas or the injectors aren't firing anymore. I pulled out the spark plugs this morning, 3 were soaked with gasoline and the 4th was dry. When I start the engine, there are no sparks, I put a piece of tissue on the top of each hole in the injector and the 3 drenched with gazoline leap out, however the 4th one stays shut. I tested the ground connection of ECU pins 14,30 and 48/55. I got zero ohm. Therefore, i think the issue is elsewhere.

I also tried to reset PID without success. The car will start when the G28 is unplugged, and it is running fine with the G28 connected. However the intermittent misfire issue continues to occur at higher RPM. The temperature sensor for coolant (G62) shows the wrong temperature of -49c, even if I unplug it. I also noticed that the oil pressure gauge in the cockpit is showing 2 bar while the actual pressure is 0.0 when i rev the engine.

I don't know what to do. I believe that I've eliminated everything else. But i'm worried that i might have missed something. Let audi key replacement near me know If you have any suggestions! TIA!

3. Fuel Pump

The fuel pump in the g28 is activated by a signal sent from the RPM sensor. The GM-style sensor is identical to the G4 and both are used in the 80 100, 200, UrS and RS2 cars so you can easily find one at a wrecking yard or from a parts store. It is simple to test them to do - just put your DMM in resistance mode and take measurements between pins 1 (with the bump on the connector's side up) and 2 (2nd from left on the black connector's end). They should be infinite Ohms.

4. ECU

Our 20vt turbo (3B AAN, ABY and ADU) engines have an ECU that needs to know the position and speed of the crankshaft in order to make decisions regarding timing of the fuel injectors, etc. It uses a Crank Position Sensor G4 and an Engine Speed Sensor G28 to achieve this. If either of these go wrong, you will receive codes on the diagnostic scanner that can lead to engine shutdown.

A damaged G28 sensor could cause an inaccurate speed counter for the gearbox and a gearbox which shifts more quickly than normal, and/or an unfire when in the gear. It is probable that your sensor is failing and needs to be replaced if you notice any of these symptoms. They are cheap and easy-to-find especially if they're an Bosch model like ours. If you prefer, GM's version of this part is an option.

5. Tachometer

A faulty engine speed sensor could be a cause for numerous issues with your vehicle. It's a crucial component of the transmission of your replacement audi key fob since it sends information to the ECU regarding how fast or slowly the engine is spinning. If this sensor fails, it will affect the performance of the transmission and the other car key replacement audi's components.

The G5 engine speed sensor is located at the outside of the transmission just above the flywheel ring gear. It sends a signal to the ECU at pin T55/49, via a grey wire. The ECU utilizes this signal to regulate fuel and boost, and also timig. It also sends it to the G5 Tachometer in instrument cluster. You can check the sensor for any failure by checking the continuity between it and the tachometer, between the ECU pin T55/49 and the instrument cluster connection on pin T6a/1 (trace [79trace [79]) as well as between T6a/1, and the instrument cluster pin T26a/12. It should show approximately 1000 ohms of resistance between those points. This is a typical part that is found across the audi keys replacement cost 80, 100 200, UrS and RS2 range from 1985 MC through the 1997 UrS AAN and 1995 RS2 ADU, so the best parts could be found in wrecking yards.