Main Page
How to Replace a Kia Sportage Replacement Key
For a number of 2012 kia rio key fob programming Kia Optima Key Fob (Www.Hulkshare.Com) models keys, the key has an integrated keyless entry system. This key is similar to a remote control and is exchangeable by a Kia dealer.
Key fobs may stop working for several reasons, including an empty coin battery worn buttons signals, water damage, signal interference and a faulty receiver module. Here are some suggestions on how you can get your Kia Sportage replacement key back to working.
How to replace the remote key or smart key?
No matter if your Kia is equipped with an intelligent key, remote key push to start key, or a regular non-transponder steel key The battery inside these keys will eventually require replacement. This is especially relevant if your vehicle displays a message that indicates that the smart key or remote is not powered by the battery.
This is a relatively easy process. To replace the battery in the keyfob remove the mechanical key from the slit at the back of the fob. Then, you need to pry the cover off. Inside the key fob there will be the small screw that holds the battery in the correct position. Using a small screwdriver, loosen the screw and remove the battery that was in place. Then, you can insert the new battery and close the slit on the key fob.
When the key fob is equipped with a fresh battery, test it by pressing the lock and unlock buttons. It's good if the doors lock and unlock as expected. You can now use kia car key replacement cost's hands-free lock/unlock function whenever your fingers feel cold or you have to run some errands in Brandon.
Not all keys may require to be programmed (transponder chips or smart keys). This requires a particular programming machine that only the dealer or locksmith can access. Other keys (non transponder metal keys) do not require programming. If your keys need to be reprogrammed, then you will need to know the key code number stamped on the tag of the key code and save the number in a secure place.
How do you replace the battery?
If the 2006 kia sportage key fob key fob doesn't respond to pressing the lock or unlock button, it is most likely that the battery is insufficient. A weak battery can cause other issues, such as the check engine light turning on or delayed engine cranking. Fortunately replacing the battery on the key fob is a relatively easy DIY project that requires just a few basic tools.
Be sure to turn off your vehicle and shut the doors before you begin. Find the small metal or plastic piece near the bottom of the key fob. Press it until the key is released. Then, you can insert the key into the driver's door handle to open your car.
To replace the key fob battery, remove the cover from the back and use a plier bar tool to loosen the latch that holds the black negative battery cable. Remove the old battery and align the new battery to ensure that the "+" positive side is facing you, while the "negative" negative side is facing the fob's metallic electrical contacts. Avoid using excessive force when pushing the new CR2032 into place to avoid breaking or bending the steel contacts.
Once the new kia key fob battery is installed and the key fob is turned on, turn it off and back on in the ignition repeatedly until the door locks. Then you can test your Kia key fob to check if it is working properly again.
How do you replace the smart key?
Depending on the model of the Kia Sportage, you may have an ordinary key fob or a smart key. The difference between the two is that the smart fob has an incredibly small key blade tucked inside it, while the standard key fob does not. Both key fobs contain batteries that eventually require replacing. This is a simple procedure that takes just two minutes.
Before you begin it is important to make sure that you are on a level surface with good lighting and that the Kia is off. Keep in mind that there are tiny pieces inside the fob which could be removed if not cautious.
The release button for the small size is located on the lower backside. This will either be an oval silver button or a rectangular slot. You can open the key fob by pressing the button.
Once the key fob is open, remove the battery that was in it. The new battery is C2032, and can be bought online or in your local auto parts shop. Once you're done, your key fob should permit you to lock, unlock, and start your vehicle even if it's not running.
How do you replace the mechanical key
The Kia key fob is a wonderful convenience that lets us lock and unlock our vehicle with the touch of the button. Like any other device, the Kia key fob might have issues. There are ways to address these issues and keep your key fobs running for many years.
A dead or low-quality battery is one of the most common issues. The battery could cause the device to stop working or work intermittently. If this is the case then try replacing the battery with a new one.
If this isn't enough to resolve the issue, try using a standard flathead screwdriver to open the fob's plastic casing. Be careful not to harm any internal components or scratch the plastic. After opening, carefully remove the battery you have been using and replace it with a brand new one.
Close and open the door with the mechanical key. (Every kia key programming fob comes with an emergency mechanical key which will fit into the slot). Test the key fob to verify that it's working as intended. Contact a dealer, or a locksmith to resolve the problem if the fob is still not working. Make sure they cut you an emergency key that works in all the trunk and door cylinders in order to prevent lockouts in the future.