The 3 Biggest Disasters In Audi G28 History
How to Replace an audi a3 key replacement G28 Engine Speed Sensor
Charles the Humble Technician teaches how to replace audi key the G28 Engine Speed Sensor. This sensor is situated near the transmission's edge over the flywheel gear. It transmits a signal to the ECU via an uncolored wire T55/49, then to the tachometer located on the instrument cluster.
1. Engine Speed Sensor
The sensor is located at the edge of the transmission above the flywheel ring gear, the G28 Engine Speed Sensor sends an electrical signal to ECU pin T55/49 via the grey wire. The ECU then uses this information to control fuel, replacement timig and boost. It also sends signals to the G5 Tachometer located in the instrument cluster.
The sensor is used as a reference point to connect with the G40 Camshaft Position Sensor. The ecu must be aware when the crankshaft is TDC and the location of the camshaft so it can start spark and injectors according to the situation.
If this sensor fails, the ECU will display an error code P00160 which indicates that the Crank Shaft and Intake Camshaft are not in sync and possibly indicating chain stretch or a jumped link on the upper chain of timing. However, the error code won't appear on its own without additional information from other sensors (G4 and G40).
It is a little tricky to test as there are several pins on the connector and they all have different functions. The most effective method to test it is to measure the resistance between the ECU and the sensor. It should read approximately 1000 ohms when the sensor is in full operation. Examine for evidence of coolant or oil in the connector bay if there are issues with this part.
2. Injectors
Yesterday, as i was accelerating off the highway paytoll at a high speed I noticed a significant decrease in power. It was like the engine had run out of gas. Or, my injectors were not firing. I pulled out the spark plugs this morning, 3 were soaked with gasoline and the fourth was dry. I put tissue over each hole in the injector and when i turn the engine on without sparks, the 3 with gazoline jump out. The 4th one remains closed. I tested the ground connection on ECU pins 14/55/30/55/48/55/14/55/48/ i get 0ohm. So i assume the problem is in another place.
I also tried to reset PID but without success. The car can start if the G28 is disconnected and it runs perfectly when it is plugged in however it has the intermittent misfire issue at higher RPM. The coolant sensor (G62) even when unplugged, still shows an ice temperature of -49c. I also noticed that the oil gauge in the cockpit shows 2 bars but the actual pressure is zero.
I'm not sure what to do, i think i've pretty much completely ruled out all other possibilities. But i'm worried that I might have missed something. Let me know should you have any suggestions! TIA!
3. Fuel Pump
The fuel pump in the g28 gets a signal from the RPM sensor. The GM-style transmitter is identical to the G4 sender and works on the 80,100,200, UrS, and RS2 vehicles. It is easy to find an extra in a wrecking shop or a parts store. It is easy to test them - simply switch your DMM into resistance mode and measure the distance between pins 1 and 2 (with the bump at the connector end facing upwards). They should be infinite Ohms.
4. ECU
The ECU in our 20vt turbo (3B AAN ABY ADU) engines must know both the position and speed the crankshaft to make decisions regarding timing of fuel injectors, etc. To do this, it utilizes a Crank Position Sensor (G4) and an Engine Speed Sensor (G28). If you are experiencing issues with either of these, the diagnostic scanner will show the codes that could trigger an engine shutdown.
Some of the symptoms of a failed G28 sensor are an inaccurate rev counter for the gearbox, gears shifting quicker than normal, and/or a misfire when in gear. If you have any of these problems, it is likely that your sensor is failing and should be replaced. They're cheap and easy to find particularly in the case of a Bosch model like ours. You can also choose the GM version of this component is also a good choice.
5. Tachometer
A damaged engine sensor could cause a variety of issues within your vehicle. It is an important part of the transmission of your spare audi key, as it transmits information to the ECU regarding how fast or slow the engine is turning. When this sensor fails, it will cause problems for the transmission and the other car's components.
The G5 engine sensor is located at the outskirts of transmission, above the flywheel ring. It transmits signals via a gray wire to the ECU pin T55/49. The ECU uses this signal to control the flow of fuel and boost and also timig. It also relays it to the G5 Tachometer in instrument cluster. You can determine if the sensor is in failure by checking continuity from the sensor to the tachometer. Additionally, you can check continuity between pin T55/49 of the ECU and pin T6a/1 of the instrument cluster (trace [79]), and between pin T6a/1 as well as pin T26a/12. You should see a resistance of approximately 1000 ohms in these areas. This is a common feature across the audi replacement key service near me 80-100-200-RS2 model, ranging beginning with the 1985 MC and up to the 1997 UrS AN and 1995 RS2 Du So, you may find good ones in wrecking yards.