Its History Of Subaru Replacement Keys
how much does a subaru key fob cost to Get a New Key for Subaru
You can lock and unlock your Subaru at the touch of an electronic button if it is equipped with a keyfob. If the key fob was dropped in the ocean, or washed in the washer then it might not function.
Our Stocker subaru replacement key dealership can help. You'll have to remove the key fob's case to locate the transmitter circuit.
How to get a new key
It's much easier than you think to obtain a brand new Subaru key. You can get a key from a dealer locksmiths, or even online. The cost varies depending on the location you purchase the key, and if it requires programming. It also depends on what kind of key you have (transponder smart fob, push to start regular non-transponder).
If you're in search of an updated key for your vehicle, it's best to call an auto locksmith who specializes in Subaru automobiles. They will know about the unique key fobs, as well as the key programming that is provided with them. If you're unsure which type of key you're using, check the sticker on your windshield to figure it out.
Certain keys come with Remote Start features that let you start your vehicle from the comfort of your home. However, you'll need to have the VIN number of the car which is on the label in the door for the driver or in the owner's manual.
Subaru models manufactured after 2000 include a transponder key that disables the engine computer. These keys cannot be duplicated using the same equipment that are used to cut keys made of metal. You'll need to visit a dealership or locksmith to purchase replacement keys. A new key can cost anywhere from $50-$250, based on the type of key and the features.
how much to replace a subaru key fob can I get a new key
There are a few ways to obtain an additional key for your subaru outback key replacement cost, depending on the kind of car you have (chip, intelligent fob or "push to start" remote, or a regular key made of metal). Contact the dealership where you purchased the vehicle for a replacement, an locksmith in the automotive field who has required equipment to make keys of these kinds or purchase one online. When you receive a new replacement key from the dealer, it will be guaranteed to work with your vehicle, be under warranty, and will include the correct programming for the specific model you have.
The dealer will require codes for the car you bought to make a chip key. This is only possible through the dealer from which you bought your car. This can be somewhat of a hassle due to the fact that you'll need either take your vehicle there or have an automotive locksmith arrive and code the key on site.
A simple key made of metal does not need to be coded and is easily duplicated by hardware stores or locksmiths who have a range of blank keys. You'll need a metal key or flathead screwdriver to unlock the tabs that are small at the top of the key fob, and take the battery off. Replace the battery with the CR2032 coin cells and then snap the encasement back together.
How to get a key Fob
A key fob can be described as a small remote device that allows you to control the electrical systems. Key fobs can be used to unlock and start your vehicle or lock it, set the alarm, and much more. If your Subaru key fob isn't functioning properly, you may need to replace it. But, you must make sure you get the correct type of fob for your vehicle. Consumer Reports says that off-brand fobs may cause problems with the immobilizer system of your vehicle.
If you have a newer Subaru model, it's likely it has an intelligent key system. These smart keys require special programming to work with your car. This is best handled by your dealer and the cost may be covered by your warranty or roadside assistance program.
Older Subaru models come with a standard metal lock that can be duplicated at a hardware store. You can also purchase blanks from online retailers that sell Subaru keys with Subaru logos.
You can repair the problem with the battery on your older Subaru at home without the need to visit a mechanic or pay for a key duplication service. Find a small crevice in the seam between the front and back of the fob. Make use of a flathead to pull off the two halves. There's a flat battery inside. Replace the old battery with a 2025-type one Make sure the correct side is facing up. After that, put the key from the metal into the battery and then pop it all together.
how much to replace a subaru key fob do I replace a key fob
In the past, people could purchase a cheap keyfob at an hardware store or on the internet and then take it to a dealership or locksmith to have it cut and programmed. It's still possible to do this, but it's best to go through the dealer. This will stop the key from being copied and ensure that the new key fob is correctly programmed for your car. This is particularly important for vehicles with newer model that requires specialized programming, such as ones with features like automatic parking and window rolling.
While these keys add to the convenience of driving your Subaru in Gilroy However, they can be a pain when they stop working. You can replace the key fob's battery yourself, as long as you're familiar with the process.
Begin by locating the small space between the front and the back of your key fob. Use the tip of a key made of metal or a screwdriver with a flat head to break open the fob and look for the round flat battery inside. Remove the old battery and then put a new 2032 battery into its spot, making sure it's in the same direction that the original one. Reassemble your fob.
In the near future, you may be able to have your car keys replaced with "smart" keys that come with added functions. But, until then you will be able to enjoy all of the benefits of your Subaru's key fob, which includes the ability to automatically open your windows while keeping your engine running.