What Experts Say You Should Know
Peugeot 208 Key Replacement
Peugeot 208 key replacement should be left to experienced auto locksmiths who have the appropriate equipment and technical know-how. They can create and program keys more quickly and at a lower cost than dealers.
If your key fob has stopped locking or unlocking your doors, it is likely due to a dead coin battery. There are other reasons why the key may be malfunctioning.
Dead Coin Battery
A dead battery in the coin compartment will stop your Peugeot 208 from locking or unlocking and will not allow you to start the engine. In this case, you will need to choose the alternate method to start found in your vehicle's owner's manual.
The spark plugs could also be worn out. The spark plugs ignite fuel to start the engine. They have a limited life span. If they are not used enough to last, they'll eventually fail.
There is a simple solution to this issue. Check the voltage of your battery with a multimeter. If it's less than 11.5 Volts then you must replace it. If the battery is damaged it is necessary to clean its contacts. This can be accomplished by removing the rubber covers from the two battery terminals, and then using a wirebrush to eliminate any parts of the battery that are corroded. You should then reconnect the cables that connect the positive and negative poles.
Water Damage
If your 208 doesn't start and the battery has not failed, you should inspect the spark plugs. It could be that they're dirty, causing them to not to spark. The spark plugs can be cleaned in a workshop.
Peugeot cars use keys that are transponder-type and works with the car's immobiliser system. This guarantees that only the right key can start the engine. If the chip inside the Peugeot key is damaged, then it will not send the proper signal to the vehicle.
Water damage is a common cause of this issue. This is particularly prevalent in colder climates. the vehicle could have been exposed to rain or snow. In this case, contact a reputable locksmith who will have the tools and equipment required to change the key's programming. They also have the most up-to-date technology and equipment needed to create a Peugeot 208 smart key. The process should not take more than 15 minutes.
Contacts for the battery that are defective
peugeot partner key replacement changed from the old carbon-encased transponder chips and introduced a new type of chip that incorporates electronic components within a circuit board. The new system is great when it's new, however the circuit boards degrade over time and cease to function properly.
This could stop the immobiliser from triggering so that your vehicle won't start. Contact an peugeot 206 key fob specialist, or a locksmith if this is the case.
A common problem is when the battery of the key fob begins to fail. This causes the blade of the key to stop feeding into the lock. A car locksmith will replace the battery, and cut a new blade for you. This is a simple solution.
Faulty Receiver Module
If your peugeot 107 key fob programming key fob stopped working after dropping it on the ground, being exposed to a sudden downpour or accidently washing it the wrong way, it could be due to a faulty receiver module. The receiver is responsible for sending radio frequency signals to an on-board computer, which controls the central locking system of your Peugeot vehicle.
The rubber seals on the key fob block water from reaching the electronic chip. Water can damage the chip if it is exposed to water for a prolonged period of time. The high salt content in the pool or ocean waters can cause damage to the key fob, especially if it is submerged.
The module must be replaced if your Peugeot spare key does not work anymore. This is only completed by an experienced auto locksmith or Peugeot specialist. In contrast to other vehicles, Peugeot keys are protected by an unique immobilizer system that requires the right coding to begin the engine. It is for this reason that you should only trust the Peugeot locksmith to design and program an alternative.
Computer on board is not working properly
The on-board computer inside your Peugeot is responsible for many of the systems within your car, ranging from airbags to power windows. The computer on board will display the code when something goes wrong. This code is stored in the system and will stay there until the issue is solved. Often, this will involve the on-board computer being replaced.
The most typical reason for the warning light for the airbag to turn on is corrosion or loose connections within the sensor. This can occur due to wear and tear, aging or exposure to salt and moisture. This issue must be dealt with as soon as you can, as an airbag that's malfunctioning could pose danger in the event in the event of an accident.
If your peugeot boxer key fob programming is showing a card not detected error, then the key battery in the key fob may be weak or dead. This prevents the key fob from sending a signal that disables the standard immobilizer in your vehicle. Try this by pressing the unlock button on the key fob, and then trying to start your car. If this doesn't work then the battery in the key needs to be replaced.