The 10 Scariest Things About Car Key Button Repair

Car Key Button Repair

A broken car key button can be a hassle. You may need to call an emergency locksmith service 24 hours a day to assistance or to purchase a new remote key repair.

You could save money by repairing your old key fob instead of replacing it. This is particularly true if the problem is due to an old switch or a damaged contact.

Battery

If the buttons on the key fob aren't responding to pressing it, this could be a clear indication that the battery is dying or nearing the end of its life. Fortunately, replacing the battery is a simple task that you can complete on your own instead of hiring a locksmith or dealer to take care of it.

Locate the battery compartment first. The battery compartment is usually located on the back of the key fob, and may be concealed behind a cover that can slide out or a button that opens the access point. After the compartment is open, look for the small button-cell battery. It is usually shaped like an oblong coin and is has the plus and minus signs. Take the battery out and insert a new one in its place, ensuring that the plus and minus signs are correctly aligned.

Once the battery is installed Close the compartment and snap the two parts of the key fob together. Before closing the door make sure to align and snap the parts in place. Press any of the buttons to confirm that they function correctly.

If your remote key fob ceases working after replacing the battery, it may be suffering from other issues that require a different kind of repair. Dropping the device into a pool of water can cause it to cease functioning. It could also be due to a malfunction with the internal electrical system or the need to be deprogrammed. See if you can find out what's wrong with your key fob using these other common methods for troubleshooting your car.

Switches

There are various types of switches found in the car key fob dependent on the year and make. The older model keys repair usually have an additional chip that is visible in the case, whereas modern keys are more sophisticated and function by sending signals to the car. Regardless of the type, the buttons on the key may get worn down or damaged during normal use. This causes them to become difficult to press or even ineffective. If you attempt to press the button too hard, it can cause further damage and may even stop the key from being able to start your vehicle in the future.

If you are unable to get your key to work, try changing the batteries. If that doesn't work then you might need to clean your key fob and re-adjust the switches. Because these tiny electronic switches spend a lot of time getting jostled around and tangled, they are more likely to wear out than larger parts of your key.

The switches are rubber-like and are coated with an electrically conducting film that wears down over time. However, they're tiny and affordable to replace. The old ones are soldered to the circuit board, so you'll have to take care to remove them without damaging anything else. Then you can put in the new ones and reassemble your key fob.

Don't use your car key fob for more than two hours at a time and do not leave it open. Also, try how to repair broken car key locate a safe place to keep your key in when you aren't using it.

If you've already tried cleaning your key fob key repair or replacing the battery, but the problem persists it's time to think about hiring an appointment with a locksmith. A professional locksmith can test your key's frequency to see if your vehicle is still able to communicate. They can also open and replace microswitches as well as change cases, and much more.

Outer Case

Key fobs spend many hours bouncing around and if the buttons aren't free to move up and down within the case they can get stuck or even broken. If changing the battery or cleaning with an alcohol-based swab and a cotton pad rubbing alcohol don't resolve the issue, taking off the case and checking it out could be required. If the contacts that the buttons touch aren't an ideal fit, or if they are worn, changing them might be the only option.

Rubber buttons be worn out over time. Rubber buttons can become hard to press as they stretch, and nails could cut them. This can cause the key to fail and in this instance it's time for the replacement of the case or buttons. This repair involves disassembling the remote, locating the buttons on the circuit board, then heating the solder, and then carefully taking them off. The new buttons are then connected to the circuit board. The case can be reassembled, and the horseshoe key blade can be attached. The new buttons must be securely fitted into the case to prevent them from falling out.

Inner Case

Since your key fob is likely to get jostled around and may occasionally be pressed by accident, the buttons inside can be damaged or stuck over time. Using metal tape and a hole punch you can often quickly solve this issue in the event that your vehicle isn't at home and the key fob won't work and allows you to open the doors, but not to start the engine. This quick fix could allow you to safely make it back to your car and finish your trip.