The 10 Most Scariest Things About Car Key Button Repair
Car Key Button Repair
A broken car key can be a source of frustration. You may need to call an emergency locksmith service that is available 24 hours a day for help or purchase a new remote.
However, you may be saving money by fixing an old key fob instead of replacing it. This is particularly true if the problem is due to an old switch or a damaged contact.
Battery
If your key fob's buttons do not respond when you pressing them, this could be a sign the battery is dead or is nearing its end of life. Fortunately, replacing the battery is a simple task that you can complete on your own rather than paying a locksmith or dealership to take care of it.
First, locate the battery compartment. The battery compartment is usually located on the back of the key fob and can be concealed behind a cover that can slide out or a button that opens the access point. When the compartment is exposed you can look for the tiny button-cell battery. It is usually shaped like the shape of a coin and is marked with an plus and minus symbol. Remove the battery from the old one and replace it with a new one in its place, ensuring that the plus and minus marks are correctly aligned.
Once the battery is installed, close the compartment and snap the two halves of the key fob together. Before closing the door make sure to align and snap the components into place. To test whether the buttons function properly, press any of them.
If the remote key fob you have purchased stops working after replacing the battery, it might be suffering from other issues that require a different kind of repair. Physical damage caused by dropping the fob in a puddle, for example, can sometimes cause it to cease functioning completely. It could also be due to a problem with the internal electrical system, or it may need to be deprogrammed. See if you can find out if the problem is with your key fob by using these other common methods for troubleshooting your car.
Switches
Based on the year and make, there are different kinds of switches that are found on the car key fob repairs keyfob. The older style keys have a chip that is visible inside the case. The modern keys repair function by transmitting signals to your car. Whatever the model of key, the keys' buttons can get worn down or damaged when used regularly. They become difficult to press or unresponsive. If you attempt to press the button too hard, it can cause further damage and may even stop the key from being able to start your vehicle in the future.
If your key doesn't appear to be working, you should first try changing the battery. If this doesn't work, then you might need to clean your key fob or re-adjust the switches. Because these tiny electronic switches spend a lot of time being tossed around they are more prone to break down than the larger parts of your key.
The switches have a rubbery feel and are coated with a film that conducts electricity. The film is prone to wear off over time. They're fortunately a very small part and inexpensive to replace. They are soldered onto the circuit board, which means you need to carefully take them off without causing any damage to anything else. Then you can put the new ones in and rebuild your key fob.
Avoid using your car key fob for more than an hour at a stretch and avoid leaving it visible. If you're not using your key, keep it in a secure location.
If the issue persists after you have cleaned your key fob, replaced the battery and attempted to clean it, you may need to talk to an expert locksmith. A professional locksmith can test the frequency of your key to see if it's still able to communicate with your vehicle, and open and replace micro switches, alter cases, and more.
Outer Case
If the buttons can't move freely up and down in the case, they may be stuck or even break. If cleaning the case using rubbing alcohol and a cotton swab doesn't work, it might be necessary to remove the case. If the contacts that the buttons touch aren't fitting well or are worn out, adjusting them may be the only option to fix the problem.
Some keys use rubber buttons which can be worn out over time. The buttons made of rubber can become difficult to press because they stretch, and nails can scratch them. This can cause the key to fail and, in this situation, it is time for a new case or new buttons. This repair involves disassembling the remote key fob repair near me, finding the buttons on the circuit board, heating up the solder and carefully removing them. New buttons are then soldered to the circuit board. The case can be reassembled and the horseshoe key blade can be inserted. The new buttons should be tightly fitted into the case in order to prevent them falling out.
Inner Case
Over time the buttons on your key fob could become damaged or stuck as a result of the constant jolting and accidental pressing. Using metal tape and a hole punch, you can usually solve this issue in the event your car is away from home when the key fob doesn't work, allowing you to unlock the doors, but not start the engine. This quick fix may allow you to safely return to your vehicle and complete your trip.