The 10 Scariest Things About Car Key Button Repair

Car Key Button Repair

A damaged car key button can be a hassle. You may need to contact a 24-hour Locksmith Service or purchase a replacement remote key repairs.

But, you may be in a position to save money by repairing a worn-out key fob rather than replacing it. This is especially true when the issue is caused by the worn-out switch or defective contact.

Battery

If your key fob's buttons are not responding to your pressing them, this could be a sign the battery has died or is nearing its end of life. It's easy to replace the battery on your own, rather than paying for an auto locksmith or dealership.

Locate the battery compartment first. The battery compartment is usually located on the back of the key fob, and is often concealed behind a cover that can slide out or an open button that opens the access point. Once the compartment has been opened then look for the small button-cell battery. It is usually shaped like the shape of a coin and is identified with a plus and the minus symbol. Remove the old battery and replace it with a brand new one. Check that the plus and minus symbols are aligned correctly.

Once the battery is installed close the compartment and snap the two parts of the key fob together. Before closing the door, align and snap the components in place. Press any of the buttons to verify that they work properly.

If your remote key repair near me key fob stops working even after you replace the battery, it may be experiencing other issues that require a different kind of repair key fob. Dropping the fob into a pool of water can cause it to cease functioning. It could also be due to a problem with the internal electrical system, or it may need to be deprogrammed. Take a look at these other auto troubleshooting techniques to determine whether your key fob is having a problem of its own.

Switches

Based on the year and the model, there are a variety of kinds of switches available that are used in the keyfob of your car. The older type of key usually has a separate chip that you can see in the case, whereas the newer keys are more advanced and work by sending signals to the car. Regardless of the type, the buttons on the key can become worn out or damaged during normal use. They become difficult to press or not responsive. If you attempt to force the button to work, it can cause further damage, and could even prevent the key from being able to start your vehicle in the future.

If you are unable to get your key to work, try changing the batteries. If that doesn't help then you might need to clean the key's fob and re-adjust the switches. Because these tiny electronic switches are constantly getting jostled around and tangled, they are more likely to break down than the larger components of your key.

The switches are rubber-like, and are coated with an electric conductor film that wears down over time. However, they're a very small part and affordable to replace. They're soldered to the circuit board, therefore you must carefully remove the old ones without causing any damage to other components. Then you can solder the new ones in and reassemble your key fob.

Do not use your car key fob for more than an hour at a stretch and don't leave it out in the open. Also, try to find a secure location to store your keys when you're not using it.

If the issue persists after you've cleaned the key fob or battery, and attempted to clean it, then you may need to talk to a locksmith. A professional locksmith can check the frequency of your key to determine if your vehicle is still capable of communicating. They can also open and replace microswitches, alter cases, and much more.

Outer Case

Key fobs spend much of its time bouncing around, and if the buttons aren't free to move upwards and downwards within the case, they may become stuck or broken car key repair near me. If cleaning the case with rubbing alcohol and a cotton swab doesn't work, it might be necessary to take off the case. If the contacts that the buttons touch are not suitable for the application, or if they are worn, changing them might be the only option.

Rubber buttons get worn out over time. The rubber expands, nails gouge into it, and the buttons become difficult to press. In this situation, the key may fail and it's time replace the case or buttons. This repair involves disassembling your remote, locating the buttons on the board, then heating the solder, and then carefully removing them. The circuit board is then soldered with new buttons. The case can be rebuilt and the key blade of the horseshoe can be inserted. The new buttons should be snugly fitted into the case to keep them from falling out.

Inner Case

Since your key fob is likely be tossed around and occasionally be pressed by accident and the buttons inside may get damaged or stuck over time. Using metallic tape and a hole punch you can solve this issue in the event your car isn't at home and the key fob isn't working, allowing you to unlock the doors, but not to start the engine. This simple fix can enable you to safely make it back to your car and continue your journey.