The 10 Most Terrifying Things About Repair Car Keys

How to repair car key fob Car Keys

The car keys aren't big and may not be considered important, but they're essential for the proper operation of your vehicle. Replacing an old key or a transponder key that is modern can cost up to $200.

There are many ways to keyless entry repair your car keys yourself at just a fraction of the cost. This article will cover the most frequently encountered car keys problems and the DIY solutions.

Dead Key Fob Batteries

Cars are equipped with remote mobile key fob repair fobs which makes opening doors and trunk easier than ever. However, the battery inside this device can die. There are, however, a few techniques that can be employed to solve this problem in the event of a need.

First, make sure that the car is in ignition mode. If it is the battery of the key fob might be low instead of dead. To test, press the button on the fob against the ignition button on the vehicle. If it works, the battery is likely fine and needs to be changed.

To replace the fob battery, first pry open the case with an instrument like a screwdriver, or watch-type tool. Be cautious not to press too hard as this could cause the fob to split in two. If the fob won't open, try using your pry tool more than once around the outside of case.

Once the fob is open take out the mechanical key and open the electronic part of the car. Then, insert the battery replacement and then snap the shell together. If the key fob doesn't work after this, there could be a bigger issue with your car's remote start system that requires a professional diagnosis. A trusted mechanic will be capable of helping you if this is the situation. If you require assistance with your vehicle or vehicle, you can get roadside assistance.

Broken Key Ring

If your key fob isn't functioning because the ring has broken there are a few options you could try. Check to see if you can locate the broken piece inside the ignition. If it's still inside it, remove it without damaging either the ignition lock or the door lock. If you're having difficulty getting it out, contact a locksmith for help. They have tools that are able to safely remove the damaged key from the ignition.

Another common cause of the car key breaking is the corrosion of the circuit board or frame. You can clean the circuit board by using a cotton swab and ruby alcohol. This will remove any corrosion and ensure the contact pads aren't damaged.

If your key isn't starting because the ring broke it, you might be able to fix it by using a thick wire or nail to close the hole. Superglue can also be used to repair car key a damaged ring. After cleaning the ring with a wet cloth, apply a small amount superglue to each end of the wire or nail. Then, press the pieces together and let them dry prior to using your vehicle. These DIY solutions may seem appealing, but they're only temporary solutions. For long-term repairs, you'll want to get a professional locksmith. They have the expertise and tools to keyless entry repair a broken key quickly and efficiently. They can replace the battery and reprogram your key fob, if needed.

Broken Key Blade

Some key blades break from a lot of wear and tear. If this occurs, you must purchase a new one. Fortunately, this issue isn't as bad as it appears at first. The primary problem is that the blade has separated from the case.

One way to fix this is to spray the key hole with a oil-based lubricant. Then, you can use pliers, pins, or tweezers to grasp the end of the broken key and pull it out. If the key is magnetic, you can also try using a magnet to help pull it out. Use a magnet as a aid to you remove the key, but be careful to not break the lock tumbler.

If you're unable to take the broken piece from the key, contact an expert locksmith immediately. They're equipped with special tools that allow them to safely remove keys without causing further damage.

Super glue can be used to fix a snapped lock. Apply a small amount glue to the edges of the break and press them together. Make sure the glue has dried before inserting the key into the lock. But this method isn't very reliable and you might have to repeat the process a few times before it works. Plus, the super glue may not be enough to hold the key together. Therefore, this is more of a temporary measure than a permanent solution.

Broken Plastic Loop

If your key fob's plastic loop is damaged it can render the key useless. Luckily, this is an easy fix. To replace it, you can use wire that is thick or a finishing nail. Make two holes in the plastic loop that is broken at each end of the wire or nail. Cut the wire or nail to key fob repairs width, then place a small drop of superglue into each hole. Apply the nail or wire into the holes and let them dry.

Another option is to get a replacement shell from a locksmith who sells them. They can take the programmable component of your key, transfer it to the new shell and cut a new blade for much less than the full replacement cost.

This isn't the most efficient solution, but it will help you get back on the road again if your key has broken in half. It can be difficult to fix when the blade of the key is inside the ignition, however. You could try using hair clips or needle extractor tool to remove the damaged piece of the ignition, however this is risky if you're not careful. Contact a locksmith who has special tools to safely remove broken keys from ignitions. They can also create a new key with the appropriate cuts for your vehicle's ignition to ensure that it functions perfectly when it is put into the lock.

Broken Master Key

If a key breaks inside the lock, you'll need to attempt to retrieve it before it's completely destroyed. There are a few techniques you can use, including using lubricants, tools, needle nose pliers or tweezers to take a small piece of the damaged key and pull it out.

Spray the inside of your lock with WD-40 or graphite powder. You can also employ the hacksaw blade method, which involves moving the blade along the side of a damaged key and grasping onto a few of its teeth.' If you are successful then you should be able to cut the damaged key.

Another useful tool is an extractor for keys spiral, that can be found in many hardware stores. This tool has a thin flexible rod with spiral threads that can be inserted in the keyway, and later bent to the broken portion of the key. Once it has gotten caught on the serrations, you can twist the bar into a circle and then pull it against the damaged section of the key.

It's worth attempting to remove the master key that is broken before calling an expert locksmith. If you're unable to pull a piece out, it's time to call the big guns to have a locksmith cut you a brand new key and reprogram it to the transponder in your car.