The 10 Most Scariest Things About Repair Car Keys

how to repair car key fob to Repair Car Keys

The car keys aren't big and may not seem important, but they are essential to the functioning of your vehicle. The cost of replacing a traditional or modern transponder car key can range from $200 to upwards of $200.

However, there are ways to repair your car keys at home with only a fraction of the cost. This article will go over some of the most frequent car keys problems and their DIY solutions.

Dead Key Fob Battery

The remote car key repairs key fobs that come with cars make it easier than ever before to open the trunk, doors, and the tailgate. The battery inside the device is prone to dying. Fortunately, there are some tricks that can be used to solve this problem in the event of a need.

First, determine if the car is in ignition mode. If it is the battery of the key fob could be low rather than dead. To test this, press the button on the key fob straight up against the vehicle's ignition button. If this is successful, the battery is probably fine and will only need to be replaced.

To replace the fob battery, begin by prying the case off using a screwdriver or watch-type tool. Be careful not to press too hard because this could cause the fob to split into two pieces. If the fob isn't coming open easily, try wedge your pry tool in more than one place on the outside of the case.

After the fob has been opened then remove the mechanical key and open the electronic section of the car. Then, you can insert the replacement battery and then snap the shell back together. If the key fob repair service fob isn't working after this, it may be due to a larger issue with the remote start system in your car. This requires an expert to determine the cause. A reputable mechanic will able help you if this is the situation. You can also call roadside assistance to assist with your vehicle, if you require it.

Broken Key Ring

If your key fob won't work because the ring has broken there are a few options you can try. Examine if you can find the broken piece within the ignition. If it is, remove it without damaging the lock on the ignition or door lock. Call a locksmith if you have difficulty removing the key. They have special tools that are able to safely remove a damaged key from the ignition.

Another common cause of a broken car key is corrosion on the circuit board or frame. You can clean the circuit board by using a cotton swab with rubbing alcohol. This will remove any corrosion and ensure the contact pads aren't damaged.

If your key won't start because the ring broke, you may be able to fix it by using a thick wire or nail to seal the hole. You can also use superglue to fix a broken ring. After cleaning the ring with a wet cloth, apply a small amount superglue to each end of the wire or nail. Apply the glue to the ring and let them dry prior to using your car. These DIY solutions might look appealing, but they're just temporary solutions. It is recommended to hire an skilled locksmith for any long-term repairs. They have the tools and knowledge to fix a broken car key quickly and efficiently. They can replace the battery and reprogram the key fob in the event of need.

Broken Key Blade

Some key blades might break due to wear and tear. If this happens, it's probably time to purchase a new key. This problem isn't nearly as serious as you might believe at first. The problem is that the blade has snapped away from the case.

Spraying lubricant into the keyhole is one solution to repair it. Then, you can make use of pliers or tweezers grasp the damaged end of the key and pull it. You can also employ a magnet in the event that the key is magnetic. Be careful not to use a magnetic tool on an ignition key since it could cause the tumbler in the lock to break.

Contact a locksmith right away when you are unable remove the broken piece of the key repair service. They're equipped with special tools that permit them to safely remove keys without causing further damage.

Super glue can be used to fix an open lock that has snapped. Apply a small amount of glue to the edges of the crack and press them together. Wait until the glue dries before you insert your key into the lock. This method is not very reliable, and you may have to repeat it a few times before it works. Additionally the super glue may not be enough strong to keep the key in place. This is more of a temporary measure rather than a permanent solution.

Broken Plastic Loop

If your key fob's plastic loop is damaged, it can make the key useless. It's a fairly easy fix. You can make use of wire or a finishing nail as a replacement. Drill two holes in the plastic loop that is broken for each end of the wire or nail. Cut the wire or nail to key width, then place tiny drops of superglue into each hole. Apply the nail or wire into the holes and let them dry.

A locksmith who sells replacement shells is an alternative option. They can transfer the programmable portion of your key to the new shell and cut new blades for a fraction of the cost.

This is not the best solution, but it will get you on the road once more if your key been cut in half. It can be difficult to repair if the key blade is in the ignition however. You could try using a hair clip, a needle or an extractor tool to pull the broken part out of the ignition, but this is risky if you're not cautious. Contact a locksmith who has special tools to safely remove damaged keys from ignitions. You can also have a new key that is made using the proper cuts to fit the ignition of your vehicle.

Broken Master Key

You'll need to try at regaining the key before it is completely destroyed. You can make use of tweezers, lubricants, and needle nose pliers to grab the fragments of a damaged key.

To start, spray the inside of your lock with a lubricant, such as graphite powder or WD-40. You may also try the hacksaw blade method, that involves carefully sliding the blade along the edge of the broken key, and hooking onto some of the teeth - if you succeed in doing this, you should be able remove the broken key from the lock.

Many hardware stores offer the spiral key extraction tool. It's a thin and flexible bar with spiral threads, which can be inserted into the keyway and bent to dig into the broken section of the key. Once it has gotten caught on the serrations you can twist the bar in a circle and pull it against the broken section of the key.

Before contacting a locksmith try to remove the broken master key before calling a locksmith. If you are unable to get the piece out, it's time to call the big guns and get a locksmith to make you a brand new key and reprogram it with your car's transponder.