The Ugly Truth About Door Lock Change
How to Do a Door Lock Change
Change of the door lock is an easy and inexpensive method to boost your home's security. This isn't for everyone. It requires some expertise and perseverance.
The cylinder is inside the knob's body. The cylinder is responsible for recognizing the key as it is inserted in the lock.
Take off the lock that was previously used.
The first step to replace the door lock is to remove the lock that was previously in use. It's a straightforward process, however it is important to keep certain things in your mind. Make sure the new lock is compatible with your door. This will ensure that it fits properly and does not leave a gap around the deadbolt plug or latch.
After you have removed the latch plate, you'll need to look for two bolts or screws in the casing's interior which are holding the casing to the two halves of the lock. Remove them with a screwdriver and then remove the lock from the door. If you have a mortise lock there could be a set screw located at the base of the handle that binds it to the spindle. Make use of a screwdriver for removing this screw, then remove the doorknobs.
You must also remove the latch and deadbolt plug from the hole in the door jamb. Install the new lock. If you are replacing a mortise you should measure the distance between the lock case and your door's edge to ensure that your new lock fits.
It is possible to replace your lock for various reasons, such as when you suspect that someone else has the key or you've a new roommate. In any case, you can save money by removing the lock yourself rather than paying an expert to remove it. It is much easier than most people imagine and can be done in a matter of a few minutes.
Remove the handle and trim of your door. With a flat screwdriver remove the trim. It should be possible to pull off the majority of it. In some instances you might be able to take off the handles completely. Next, look for a hole on the inside of the handle and insert an unstraightened clip into it. This will activate the release mechanism, which allows you to take off the handle. Then, look for a small tab on the interior of the upvc window lock mechanism replacement window lock replacement locks for double glazed windows (https://blogfreely.net/slopeweed09/25-surprising-facts-about-lock-replacement), and press it with a flat screwdriver. Once the spindle has been removed, you can take off the cylinder and housing.
Making a decision on a new locking system
You have many options when it comes time to pick the right lock. Consider different kinds of locks, and find one that matches your door's style. Consider the backset, which is the distance between the edge and the center of the hole for the lock. Also, consider the cross bore, which is a small hole at the edge of your door frame. Also, make sure to choose a lock that will fit the door thickness and swing.
Most door locks are assessed by BHMA and the American National Standards Institute to provide you with an idea of how well they will withstand use and how difficult to disable or pick. A lock of grade 3 could be the ideal choice for a tranquil apartment in the country, while locks that are grade 1 might be more appropriate for an area with a lot of traffic, such as the storefront.
Most smart door locks require digital code to open. If you're concerned about security breaches or hacking seek out an expert locksmith or your local police department for advice.
Replace the cylinder
If your door lock's cylinder is damaged or broken you can repair it within a matter of minutes using a simple DIY project. It is important to select the appropriate cylinder and follow all instructions. The first step is to take off the knob or handle, should there be one then loosen the trim around the base of the lock cylinder using the help of a screwdriver. After the trim is removed, you can remove the screws holding the cylinder in position with a flathead. The cylinder is then gently removed from the door.
Before installing the new cylinder, make sure that it is the correct length for your door. With a tape measure, measure the distance between the cylinder's center and the left and right sides. Then, purchase a new cylinder with the same measurements. This will prevent cylinders from snapping when the door is hit or the key is stuck inside.
Once you have a suitable replacement cylinder, place it in the door and turn the key. This will align the cylinder with the carrier that is usually located on the outside of your lock. Then, loosen the set screws that should be just a couple of turns inside the head. If there is a screw at the outside of the case, which holds the door, you'll need to remove it.
After taking the lock cylinder out after which you can replace it with the new lock by sliding the new cylinder into the case and tightening the set screw. You should also reinstall the piece that connects the cylinder with the lock indicator stem, which you can do by removing three tabs on the back of the cylinder with needle-nose pliers. Attach the bracket that is smaller to the cylinder's back. Then, you must reinstall the strike plate and latch plate, as well as the retaining ring connected to the top of the lock the cylinder.
Installing a new lock
If you're replacing a previous lock, start by measuring the width of your door lock window repairs. The majority of residential locksets are designed for a door thickness of 1 3/8 to 1 3/4 inch. If your door is thicker than 1 3/8 to 1 3/4 inches, you'll need an extra thick door kit. This would include longer screws and either a longer spindle extension or tail piece for door knobs.
The majority of locks come with a detailed instruction manual to guide you through the installation of the new hardware. Be sure to read the instructions thoroughly before beginning the process to make sure that you've followed all the steps. The manual will give you a clear idea of how much skill is required to finish the task. If you're changing locks for the first time, you might want to ask an experienced friend for assistance.
It's a good idea to tape the openings in the old hardware before installing the new lock. This will stop screws from slipping through the holes and will also protect any tiles you might have installed. It also shields your tiles from any damage caused by dirt, rust and grime. SECURAM Touch comes with a strip of painter's tape that is intended to be used for this purpose, but you can also use gaffer's tape as well as masking tape in the event that you have it.
After removing the screws that hold the lock's inner half to the exterior then remove the lock immediately. It's important to do this quickly to avoid the lock from closing itself in a way that could end up damage the mechanism.
If the new lock comes with an latch bolt, install the new bolt into its upper cross bore. Make sure that you place it in the proper location, which is indicated by an arrow. Then, place the latch plate over the bolt and secure it in place.
Finally, screw the deadbolt and strike plate to the door jamb. Check the deadbolt several times by throwing it to make sure it extends into the strike plate. Follow the instructions included in your electronic smart lock to program it. This involves downloading an app and registering your e-mail address, confirming your identity, and connecting to the wireless network in order to connect your device.