The 9 Things Your Parents Taught You About Fiat Panda Key Fob Replacement

Reasons Your Fiat 500 Key Fob Won't Work

A key fob with the fiat bravo key panda key (please click the next document) 500 number is a convenient way to unlock the doors and start the car. There are a myriad of reasons the fob could stop working. These include a dead coin battery, water damage, receiver module problems, and interference.

This listing is for an NEW replacement fiat 500 abarth key Flip Key Remote that looks like the Ilco brand. It needs to be professionally programmed (click here how to program fiat 500 key fob search for local automotive locksmiths). This remote includes lock, unlock and trunk buttons.

Dead Coin Battery

A dead battery is the main reason for your 500 key fob not functioning. Modern key fobs offer only a limited range of operation and must be within a few inches of your vehicle in order to work. If you're far away from your vehicle and press the key fob button, the car won't respond and will display the "Key Fob Not Detected" message in the instrument cluster.

If this occurs, replace the coin-cell battery (Part Number CR2032) by a fresh one of a reliable brand, like Panasonic Duracell or Energizer. They can be found in your local hardware store or on the internet.

After you've changed the battery on the coin cell, you can test it by standing close to your Fiat 500 and pressing the buttons. The parking lights should blink and the key fob should operate the lock and unlock switches.

If the key fob won't work after replacing the battery, it might be damaged by water, which prevents it from connecting to the receiver module in your vehicle. Water damage can happen in a variety of ways, such as the simple splash or submerging the key fob in saltwater at the beach. If you suspect that your fob has been exposed to water, put it in a bag of rice to draw out the moisture. If this doesn't work your fob is likely to require reprogramming by an experienced locksmith or dealer.

Water Damage

Water damage can occur if you immerse the fob in the ocean or wash it in a washer. Saltwater can cause the circuit board to short, and eventually fail. It's not good to submerge the fob in water however, don't give it up even if you accidentally drop the fob in the water or don't remove it from your pants pocket.

First, remove the battery from the fob. Before replacing the battery clean the electronic chip using isopropyl, or a similar product. Test the fob next to verify if it's working. If the key does not function, it may need to be changed. This is typically done by a dealer or professional auto locksmith.

If your key is old and has not been programmed for your vehicle, you will need to replace it completely. A professional locksmith for cars can carry out this simple task. The locksmith will require the key cut to match the car's ignition. The locksmith will also need to reprogram your fob into the car's system. This is a cheap and quick process that can be completed on the same day.

Receiver Module Issues

The 500 key fob could stop working because it is out of range. The remote has a maximum range of 30 feet. Therefore, should you be too far from your vehicle it will not respond to your commands. You can fix this by moving the remote closer to your car until it responds.

If you've replaced the coin battery (commonly known as a "button" or "watch") and your fob still won't work it could be due to an internal circuit board issue. In most cases, reprogramming the fob will solve the issue. You can find the steps for the majority of vehicles on YouTube or in the owner's manual.

It may be necessary to replace the metal clips that hold the coin batteries in place. If they lose tension, it can prevent your coin battery from being properly seated, causing your remote to malfunction.

In rare cases the fob could be out of the vehicle's sync because of hardware or software issues. This could cause a significant trouble, but you could usually fix it by visiting a local dealer or auto locksmith to have them reprogram your fob. In certain instances it may be necessary to reinstall the software in your body control module, too.

Interference

Interference can also cause the key fob not to receive or transmit the signal. This could happen when the keyfob is in close proximity to a radio transmitter such as a cell phone or radar detector. The key fob might not work due to a bad connection to the buttons or water damage, or damage to the internal chips.

If your key fob suddenly stopped working, or if you have tried everything at home to fix it (e.g. You may have a faulty 500 receiver module If you've tried replacing it with a battery, reprogramming, or using an alternative key fob. The receiver module, which is located beneath the dashboard, detects radio frequency signals from your key fob. It converts the signals into electronic commands, which are then processed by the vehicle.

Luckily, there is an easy method to reset all of the onboard systems in your 500 keys, including the key fob. Disconnect the battery for 15 minutes by taking off first the negative cable, then the positive cable. Then reconnect the battery. This will eliminate any remaining electricity and then restart the car's computers. This can help you the key fob to function again. If the issue continues, you should speak with an expert technician. They can determine the exact cause of your issue.